ARMYADP.COM
THE ARMY'S "NEW" DIGITAL RUCKSACK
← Back to TC 3-22.9 Hub

TC 3-22.9 — Malfunctions & M4 Maintenance

ArmyADP — The Army's "New" Digital Rucksack

Source: TC 3-22.9 (armypubs.army.mil)

TC 3-22.9 Para 5-1 through 5-14

Malfunctions & Immediate/Remedial Action

Para 5-1

A malfunction is a failure of the weapon to function properly. Malfunctions are classified as stoppages (temporary interruptions) or breakages (mechanical failures requiring armorer repair).

Para 5-2

Immediate action (IA) is the action taken to reduce a stoppage without identifying the cause. IA is performed automatically when the weapon fails to fire.

Para 5-3

SPORTS — Immediate Action Drill: Slap the bottom of the magazine firmly upward. Pull the charging handle fully rearward. Observe the ejection port for a cartridge or obstruction. Release the charging handle. Tap the forward assist. Squeeze the trigger.

Para 5-4

Remedial action is taken when immediate action fails to clear a stoppage. The Soldier identifies the cause of the malfunction and takes corrective action.

Para 5-5

Failure to feed: The cartridge fails to feed into the chamber. Causes include a damaged magazine, dirty chamber, or weak magazine spring. IA: SPORTS. Remedial: Replace magazine.

Para 5-6

Failure to chamber: The cartridge fails to fully seat in the chamber. Causes include a dirty chamber, damaged cartridge, or obstruction. IA: SPORTS. Remedial: Clear obstruction, inspect chamber.

Para 5-7

Failure to fire (misfire): The weapon fails to fire after the trigger is squeezed. Causes include a defective primer, dirty firing pin, or broken firing pin. IA: SPORTS. Remedial: Inspect firing pin.

Para 5-8

Failure to extract: The spent cartridge case fails to extract from the chamber. Causes include a broken extractor, dirty chamber, or swollen cartridge case. Remedial: Use clearing rod to remove case.

Para 5-9

Failure to eject: The spent cartridge case fails to eject from the receiver. Causes include a broken ejector or weak ejector spring. Remedial: Remove case manually, inspect ejector.

Para 5-10

Double feed: Two cartridges attempt to enter the chamber simultaneously. Causes include a failure to extract combined with a new round feeding. Remedial: Lock bolt to rear, remove magazine, clear chamber.

Para 5-11

Bolt override: The bolt rides over the top of a cartridge in the magazine. Causes include a damaged magazine or improper loading. Remedial: Lock bolt to rear, remove magazine, clear chamber.

Para 5-12

Hangfire: A delayed ignition of the propellant. The Soldier keeps the weapon pointed downrange for 30 seconds before attempting to clear. Hangfires are rare but dangerous.

Para 5-13

Squib load: A cartridge with insufficient propellant that may lodge a bullet in the barrel. If the weapon fires with reduced recoil or sound, cease fire immediately and inspect the barrel.

Para 5-14

Cook-off: Ammunition that fires due to heat from a hot barrel. Allow the weapon to cool before clearing. Cook-offs can occur after sustained rapid fire.

TC 3-22.9 Para 6-1 through 6-12

M4 Operator-Level Maintenance

Para 6-1

Operator-level maintenance (PMCS) is the Soldier's responsibility. Soldiers clean and inspect their weapons before and after use, and at regular intervals during storage.

Para 6-2

The M4 is disassembled into five groups for cleaning: upper receiver group, lower receiver group, bolt carrier group, charging handle, and buffer assembly.

Para 6-3

Field strip procedure: Clear the weapon, separate upper and lower receivers, remove bolt carrier group and charging handle, remove buffer and action spring.

Para 6-4

The bolt carrier group (BCG) is the most critical component to clean. Carbon buildup in the BCG is the primary cause of malfunctions. Clean the bolt, carrier, firing pin, and cam pin.

Para 6-5

The bore is cleaned with a bore brush and patches. Run the bore brush through the barrel from the chamber end. Follow with dry patches until clean, then apply a light coat of CLP.

Para 6-6

CLP (Cleaner, Lubricant, Preservative) is the standard cleaning and lubricating compound for the M4. Apply CLP to all metal surfaces after cleaning.

Para 6-7

Lubrication points: The bolt carrier group requires liberal lubrication. The charging handle, buffer, and action spring require light lubrication. The bore requires a light coat of CLP.

Para 6-8

The gas tube and gas key must be free of carbon buildup. A clogged gas system reduces the energy available to cycle the bolt and causes malfunctions.

Para 6-9

The magazine is a critical component that requires regular inspection and cleaning. Inspect the feed lips, follower, and spring for damage. Replace damaged magazines immediately.

Para 6-10

Inspection after cleaning: After reassembly, perform a function check. Verify the safety selector, trigger, and bolt carrier group function correctly.

Para 6-11

Function check procedure: Place on SAFE, pull charging handle and release, pull trigger (should not fire). Place on SEMI, pull trigger (hammer should fall). Hold trigger, charge weapon, release trigger (should reset).

Para 6-12

Weapons storage: Store weapons in a clean, dry environment. Apply a light coat of CLP before storage. Inspect weapons regularly during extended storage periods.

CONTACT